#Board And Batten Measurements Driver Used To#
#Board And Batten Measurements How To Apply This#

Board And Batten Measurements How To Apply This

Some will say to go all the way to the floor, it's up to your design preference.As youвЂ™ve seen throughout our home, weвЂ™ve done plenty of shiplap. Note I placed my base board batten on top of the existing base trim. (DISCLAIMER 1: There are lots of tutorials telling you how to apply this panelling, but lots donвЂ™t go into the details of HOW you measure everything, they just tell you to measure.Middle Vertical Boards: Take wall height (96') (width of top board + base board + base trim (5.5'+2.5'+4')) 84'. Here is a simple step by step tutorial for how I created and installed our simple and effective board and batten wall panelling.

After reading about our board and batten DIY experience, I hope you too will feel confident to try it in your home (if you havenвЂ™t already)! Planning & Thinking It ThroughDetermine height of chair rail. We felt adding board and batten would be a nice contrast to some of our other projects and that it would give us a chance to try something new. Board and batten, vertical boards with a top molding, is a design feature that we have long liked and wanted to incorporate into our home.

Since we had seen board and batten on entryways, mudrooms, dining rooms, we were stuck thinking it was a first floor upgrade. There isnвЂ™t a single room on our first floor given our open floorplan and there isnвЂ™t an accent wall that could be used without it looking forced. The first issue of WHERE has to do with our open first floor. Mark placement of board Install 1Г—4 board ( I used 1 3/4 nails and a nail gun) If you are doing the entire stairwell, continue the process up the stairs.With board and batten we faced the dual challenge of вЂњWhere the heck can I do it?вЂќ and вЂњHow the heck do I do it?вЂќ. I used a primed 1Г—4 finger board for my top board.

As we looked at his room, we could envision the board and batten and decided to run with it.6. Not shiplap) and wanted options for displaying his treasures. Porter wanted a makeover unique to him (i.e. Then we reached PorterвЂ™s room вЂ“ a bedroom with 5 doors and a large double window.

How do you evenly space the battens around the room? How high should we put the top piece? How do you attach battens if the vertical boards donвЂ™t line up with the studs? Is my level really accurate? After looking at how-to guides and watching videos, soon most of the stressed melted away. It has a comfortable, upscale farmhouse feel.Board and Batten is a siding style that combines alternating wide 'Boards' and more narrow 'Battens' that are installed vertically.The next challenge was the HOW. Board and batten wainscoting is usually applied about 32 inches up the wall, measuring from the floor. Entire walls or ceilings can be covered in board and batten, or it can be used as wainscoting.

No matter how we spaced it out, we would invariably hit a door frame or window.BUT вЂ“ measuring just the open section of wall space allowed for more flexibility in spacing. We originally measured all the wall space and struggled with how to determine how to evenly space the battens. Super simple logic but something that the HOW prevented us from seeing. Only measure each section of open wall. As I have found, any positive attitude and creative idea can be tempered by the question of HOW вЂ“ so donвЂ™t let the HOW get in your way.The planning and diagramming went quickly after a piece of advice we found вЂ“ donвЂ™t try to measure the entire room when spacing your battens. The HOW can be a blocker on any project and this was certainly the case here.

MaterialsThis was the starting point for our materials for this board and batten DIY project. This is a minor adjustment that has a big impact in solving spacing. So, throughout the room battens range between 11 вЂ“ 12.5вЂќ based on need.

Board And Batten Measurements Driver Used To

For example, we didnвЂ™t include the pry bar that was used to pull the old baseboard off the wall, or the screwdriver used to remove the outlet covers. Tools:There are always other smaller tools involved in any project, but these are the main ones that we used for this board and batten DIY project. Unfortunately, the existing trim in the room had a tapered design so when the 1Г—3 batten met the baseboard trim it left a gap that just would not work вЂ“ so the baseboards had to go. We knew board and batten would not match the trim on the doors and window perfectly, but we did not want to replace all the trim. Once we got started, I had to add 1Г—5 board to the materials list because we needed to replace our baseboards. We recommend getting the primed wood as it saves a lot of time while painting.

We did not measure from the floor or ceiling as we worked around the room, floors and ceilings can often fluctuate and could cause the top board to not be level. We have a 4вЂ™ level which was helpful when working around the doors and window. We worked around the room, using a level as we went. We applied a little liquid nails but since we nailed into the studs we knew the top board would be secure. In the end, it is basically up to you!We checked our walls and marked the studs throughout the room and then started hanging. Remember, we have lots of experience handing horizontal boards! The height was purely subjective вЂ“ Mark held the board up and I stood back and said вЂњYeah, that looks good.вЂќ You may want to consider things like light switches, future design plans for the walls, or overall aesthetic when determining the height.

We did use a nail or two which helped to seal the batten to the wall. Since most of the batten do not line up with a stud, the liquid nails is a requirement. In a similar fashion to the top board, we set our initial height (based on where the original baseboard was) and worked with our level around the room, using liquid nails and nailing into the studs.Now it was batten time! We started cutting and hanging the batten pieces based on the original diagram we created. In the end it didnвЂ™t cause a huge impact starting with the top board.After we completed the top board, we added the baseboard. We did eventually discover that the batten did not matching the baseboard вЂ“ so be sure to check that before you begin. We did not start with the baseboard because at this point we did not realize there would be an issue.

It is easier to make a decision after seeing a dry-fitted piece on the wall as opposed to a drawing on paper.Under our window we did have to trim the top edge of the batten since we once again encountered the issue with the existing trim not matching the 1Г—3 batten. There were a couple corners or awkward spaces where it was easier to line up the batten in the moment. For the most part, we followed our diagram as we worked around the room. There were still some variations as we worked around the room even with the best attempts at leveling the top board and baseboard.

The Woodland Lichen green was easy to apply but when rolling we wanted to make sure that we didnвЂ™t drip on the white that was already finished. Some people like to add a decorative trim piece below the cap but since this was for a boyвЂ™s room, we didnвЂ™t think it was needed.We allowed the white to dry for a day and then taped off the top board on the board and batten. This top ledge finishes out the look of the board and batten вЂ“ and also gives Porter a place to showcase some of his favorite Lego men or figurines! The installation went quickly as I used a little liquid nails and nailed the board to the top of the top board. In those cases, we notched the batten to allow space for the outlet cover to fit.Last up was the cap piece that went on top of the top board. Also, a few batten boards overlapped an outlet.

We also love how each of our children have a room that is unique to their tastes and gives them a personal space that is all theirs. We couldnвЂ™t be more happy with the end result. But, as is often said вЂ“ the harder the work, the better the outcome.